|
Product Details:
Payment & Shipping Terms:
|
| Standard: | IEC60884-1 Clause 23.2 | Electric Control Method: | PLC+ Touch Screen |
|---|---|---|---|
| Drive Method: | Motor And Electromagnet Drive | Tension Application Method: | Horizontal Or Vertical (optional) |
| Test Station: | Single Station | Tensile Weight: | 30N, 40N, 60N, 80N, 100N, Or 120N |
| High Light: | Cord Anchorage Force And Torque Tester,Clause 23.2 Force And Torque Tester,IEC 60884-1 Force And Torque Tester |
||
IEC60884-1 Clause 23.2 Cord Anchorage Force and Torque Test Equipment
Standard and Clause:
The Cord Anchorage Force and Torque Test Equipment is designed and manufactured according to the standard requirements of IEC60884-1 clause 23.2, IEC60745-1:2006, IEC60335-1 clause 25.15, IEC60598-1 clause 5.2.10.3, IEC60065 clause 16.5 and etc.
Prodcut Information:
The tester is used to conduct two tests of tension and torque at the terminals of appliances (lamps) with power cords, appliances intended to be permanently connected to fixed wiring with flexible cords, and power cords such as household appliances, medical equipment, etc.
The test method is to make a mark at the position of the wire sample 20mm from the fixing device, gently apply the tension 25 times (or the number of times required by other standards) at a rate of 1 time/second, and apply a torque near the exit of the appliance for 1 minute. After the test, the displacement of the marking position of the wire shall not exceed 2mm.
Technical Parameters:
| Standard | IEC60884-1 Clause 23.2 |
| voltage | 220V(AC)50Hz |
| Electric control method | PLC+ touch screen |
| Drive method | Motor and electromagnet drive |
| Test station | Single station, vertical and horizontal cannot be tested at the same time |
| Sample clamping method | Mechanical clamping, clamping point height can be adjustable |
| Tensile weight | 10N: 1 PC, 20N: 3 PC, 30N: 2 PC (The tester can test the tensile weight of 30N, 40N, 60N, 80N, 100N, and 120N) |
| Tension application method | Horizontal or vertical (optional) |
| Torque weight | 4N, 5N, 7.5N, 12.5N, 17.5N, 21.25N (The tester can test the torque weight of 0.08N∙m, 0.1 N∙m, 0.15 N∙m, 0.25 N∙m, 0.35 N∙m, and 0.425 N∙m) |
| Test times | 0~999999 times, can be preset |
| Rally frequency | 1s/time, with tension sensing clip which can verify the tension retention time |
| Torque time | 0-9999.9 seconds, can be preset |
| Equipment size and weight | WDH=650×550×1200mm, approx. 110kg |
Contact Person: Ms. Zoe Zou
Tel: +86 13527656435
Fax: 86-020-39185976
| Factory Address:Room 101, 1st Floor, No. 6, Third Street, Pingshan Industrial Zone 511495, Shibi Street, Panyu District, Guangzhou, China | |
| Sales office:Room 101, 1st Floor, No. 6, Third Street, Pingshan Industrial Zone 511495, Shibi Street, Panyu District, Guangzhou, China | |
| +86-020-39185976 | |
| sales@sinuotek.com | |
