Medical Material Tester ANSI/AAMI-EC53 2013/(R)2020 Flex Life Of Trunk Cable And Patient Leadwire Flex Relief
| Input power: | AC220V 50HZ | Control method: | PLC Control |
| Drive mode: | Servo Motor Drive | Clamping method: | Mechanical Clamping |
| Test station: | 1 Station | Flexing angle: | 0-360° |
| Flexing rate: | 0-60 Times/m | Flexing times: | 0~999999 Times |
| High Light: | Leadwire Flex Relief Medical Material Tester,：ANSI/AAMI-EC53 Medical Material Tester |
||
ANSI/AAMI-EC53: 2013/(R)2020 Flex Life Of Trunk Cable And Patient Leadwire Flex Relief
Standard & Clauses:
AAMI-EC53-1998
ANSI/AAMI-EC53:2013/(R)2020 “ECG trunk cables and patient leadwires”
Specimen Range, Application, Principle, Structure and Use Environment:
Samples and Restrictions: EGA trunk cables and patient leadwires
Application: Used to test the bending resistance of EGA trunk cables and patient leadwires when the power cord enters the appliance. To verify its reliable performance.
Principle: Use a motor to drive the fixture to flex the sample. Apply current to the soft wire to make the sample flex left and right at a certain speed and angle of ±90°. And clamp the weight at a position 6 inches away from the lead outlet end of the sample. The test will automatically stop when the equipment reaches the test times or the soft wire is short-circuited.
Equipment structure and schematic diagram:
The equipment is driven by a servo motor, and the fixture is installed in the center. And the eccentricity is adjustable. When clamping the sample, the flexing axis and the point where the cord enters the appliance can coincide as much as possible. This results in minimal lateral displacement of the cord and load.
Equipment dimensions: approximately: 800×800×1300 (mm) W×H×D, equipment weight: 130kg
Technical Parameters:
| Test station | Single |
| Electrical control method | PLC and 7-inch touch screen |
| Drive mode | Servo motor drive |
| Sample clamping method | Mechanical clamping, the position of clamping point is adjustable |
| Flexing angle | 0-360° adjustable arbitrarily (can be preset ±30°, ±45°, ±60°, ±90°) |
| Flexing rate | 0-60 times/min, variable frequency speed regulation |
| Flexing times |
0~999999 Can be preset and set according to standard table 1 requirements
|
| Load weight |
1. 0.23kg (±5%), 1 piece (weight tray). 2. 0.1kg, 10 pieces, (add weight, stack weight). Achieve standard 0.0072*π*d² (±5%) |
| Test judgment |
1. Short circuit judgment 2. Disconnection judgment |
IEC 60601-1 Medical Pressure Vessel Water Pressure Testing Machine for Safety Compliance
IEC 60601-1 Medical Pressure Vessel Water Pressure Testing Machine for Safety Compliance Product Information: Standard: IEC60601-1:2012 "Medical electrical equipment - Part 1: Generay requirements for basic safety and essential performance". Samples and restrictions: Medical pressure vessels, ...
IEC 60601-1 Oxygen Rich Environment Spark Ignition Test Chamber For Spark Ignition Test
IEC 60601-1 Oxygen Rich Environment Spark Ignition Test Chamber for Spark Ignition Test Product Information: 1. Standard: conform to IEC60601-1:2012 clause 11.2.2, figure 34-37. 2. Samples and restrictions: Medical device boards or devices in oxygen-rich environments 3. Application: It is used for ...
IEC60601-1 Fully Automated Medical Bed Comprehensive Test Device
IEC60601-1 Fully Automated Medical Bed Comprehensive Test Device Product Information: 1. Standard: conform to IEC60601-1:2012, YY9706.252-2021 clause 201.9.8.3.3 and 201.9.8.3.3.4, IEC60601-2-52:2009. 2. Samples and restrictions: the medical bed. 3. Application: it is suitable for medical hospital ...
IEC 60601-1 Human Body Weight Dynamic And Static Load Testing Machine For Medical Bed Test
IEC 60601-1 Human Body Weight Dynamic And Static Load Testing Machine For Medical Bed Test Product Information: 1. Standard: conform to IEC60601-1:2012, YY9706.252-2021 clause 201.9.8.3.2 and 2019.8.3.3, IEC60601-2-52:2009 2. Samples and restrictions: the medical bed. 3. Application: it is suitable ...
