|
Product Details:
Payment & Shipping Terms:
|
| Applied Standard: | IEC62196-1: 2020 | Applied Clause: | Clause 25.3 |
|---|---|---|---|
| Applied Figure: | Figure 17 | Test Contents: | Pull Force And Torque |
| Control Method: | Button | Drive Mode: | Motor And Cylinder |
| Torque Arm: | 100mm | Pull Frequency: | 1 Cycle/s |
| High Light: | IEC62196-1 Torque Test Equipment,Clause 25.3 Torque Test Equipment,100mm Arm Torque Test Equipment |
||
IEC62196-1 Electric Vehicle Connector Pull Force and Torque Test Equipment
Equipment introduction:
This pull force and torque test equipment is used to test the vehicle plugs, and socket-outlets, connectors to withstand the specified pull force and torque.
It is designed and manufactured according to IEC62196-1: 2020 clause 25.3 Figure 17 and table 11, IEC60309-1: 2012 clause 23.3, etc.
Equipment Principle and Structure:
Pull is realized by single-phase speed-regulating motor to drive the eccentric mechanism, the motor speed is adjustable, to ensure the accurate time for each pull force applied; torque is achieved by releasing the torque weight by air cylinder.
Technical Parameters:
| Operation Method | Button operation |
| Drive Mode | Motor and cylinder |
| Pull Force Weights |
40N*2, 50N*1, 60N*1, 110N*1,250N*1 Can achieve 160N, 200N, 240N, 250N,500N pull force |
| Torque Weights |
6N*1, 7N*1, 12N*1, 15N*1, 23N*1, 110N*1 Can achieve 0.6N.m, 0.7N.m, 1.2N.m, 1.5N.m, 2.3N.m, 11N.m torque |
| Torque Arm | Ф200mm |
| Pull Frequency | 1 cycle/s |
| Pull Cycles | 1-999999 cycles, can be preset, default 100 cycles |
| Torque Applied Time | 0-99999.9S, can be preset, default 1 min |
| Fixture | One set of universal fixtures |
| Equipment Dimensions & Weight | L 1560mm*W 600mm*H 1530mm, approx. 220KG |
| Power Supply | Single phase AC220V±10%, 60Hz, 10A |
How to select the corresponding pull force weight and torque weight?
Choose the proper weight according to following table:
|
Rated current A |
Pulling force N |
Torque Nm |
Pull weight+ torque weight selection |
Maximum displacement mm
|
| 10-20 | 160 | 0.6 | 160N+6N | 2 |
| 32 | 200 | 0.7 | 200N+7N | 2 |
| 63 | 240 | 1.2 | 240N+12N | 2 |
| 80 | 240 | 1.2 | 240N+12N | 2 |
| 125 | 240 | 1.5 | 240N+15N | 2 |
| 200 | 250 | 2.3 | 250N+23N | 2 |
| 250 | 500 | 11 | 500N+110N | 5 |
| 400 | 500 | 11 | 500N+110N | 5 |
Contact Person: Ms. Zoe Zou
Tel: +86 13527656435
Fax: 86-020-39185976
| Factory Address:Room 101, 1st Floor, No. 6, Third Street, Pingshan Industrial Zone 511495, Shibi Street, Panyu District, Guangzhou, China | |
| Sales office:Room 101, 1st Floor, No. 6, Third Street, Pingshan Industrial Zone 511495, Shibi Street, Panyu District, Guangzhou, China | |
| +86-020-39185976 | |
| sales@sinuotek.com | |
