IEC 61347-1 Thermal Protection Ballast Heating Test Chamber For Thermally Protected Ballasts
| Heated Chamber Partition: | 560mm × 560mm × 25mm | Internal Chamber Size: | 610mm × 610mm × 610mm |
| Chamber Wall Thickness: | 25mm ±1mm | Strip Heater Specification: | 40mm × 300mm |
| Temperature Control: | Three Thermocouple Inputs | Temperature Sensors: | 3 X K-type Armored Thermocouples |
| Display Panel: | 7-inch Color Touchscreen | Step Control: | Single Cycle, 8-step Programmable |
| High Light: | IEC 61347-1 ballast test chamber,thermal protection ballast tester,LED ballast heating test equipment |
||
IEC 61347-1 Thermal Protection Ballast Heating Test Chamber For Thermally Protected Ballasts
Product information:
Standard: IEC 61347-1 Annex C figure D.1, UL8750 figure 8.3, UL935 figure 25.1.
This equipment is manufactured according to the requirements of IEC61347-1:2012 standard Appendix D for the test chamber for heating test of control devices of thermally protected lamps. Due to the requirements and limitations of the standard, this test chamber does not use duct circulation. Ordinary linear heating is completely unable to meet the test conditions required by the standard. Therefore, this test chamber uses integral intelligent temperature control heating to keep the test temperature in the test chamber within 40+0-5℃.
Technical Parameters:
|
No. |
Item |
Specification |
|---|---|---|
| 1 | Overall Dimensions | 1010mm (L) × 660mm (W) × 860mm (H), including casters; subject to final delivery |
| 2 | Internal Chamber Size | 610mm × 610mm × 610mm |
| 3 | Heated Chamber Partition | 560mm (L) × 560mm (W) × 25mm (T), imported high-temperature insulation board |
| 4 | Chamber Wall Thickness | 25mm ±1mm |
| 5 | Strip Heater Specification | 40mm (W) × 300mm (L), 300W, 220V/50Hz |
| 6 | Temperature Control | Three thermocouple inputs; PLC-based intelligent PID control by average temperature |
| 7 | Temperature Sensors | 3 x K-type armored thermocouples, horizontally installed with mounting brackets |
| 8 | Display Panel | 7-inch color touchscreen |
| 9 | Input Voltage | 220V/50Hz, max. 6A, max. 1.3kW |
| 10 | Step Control | Single cycle, 8-step programmable temperature and dwell time; timing starts only after reaching setpoint |
| 11 | Dimensional Tolerances | As calibrated according to the table below |
Dimensional Tolerance Table:
|
Size Range (mm) |
Tolerance (mm) |
|---|---|
| 0.5 – 3 | ±0.2 |
| 3 – 6 | ±0.5 |
| 6 – 30 | ±1.0 |
| 30 – 120 | ±1.5 |
| 120 – 400 | ±2.5 |
| 400 – 1000 | ±4.0 |
| 1000 – 2000 | ±6.0 |
| 2000 – 4000 | ±8.0 |
IEC 60238 Clause 16.2 Figure 6 Torque Test Apparatus With Lamp Holder Gauge E14/E27/E40
IEC 60238 Clause 16.2 Figure 6 Torque Test Apparatus With Lamp Holder Gauge E14/E27/E40 This torque test apparatus is designed to comply with Clause 16.2 and 16.4 Figure 6 of IEC 60238:2016+A1:2017+A2:2020 standards for testing lamp holder durability and mechanical strength. Test Procedures and ...
IEC62560 Clause 15 Figure 8 Lamp Testing Equipment for Non Dimmable Lamps Compliance Test
IEC62560 Clause 15 Figure 8 Lamp Testing Equipment for Non Dimmable Lamps Compliance Test This testing equipment is specifically designed to meet the requirements of IEC 62560 Clause 15, providing a reliable and standardized solution for evaluating the performance of non-dimmable self-ballasted LED ...
IEC 62560 Clause 6 Interchangeability Gauges For E14 And E27 Lamp Cap 7006-28A-1
IEC 62560 Clause 6 Interchangeability Gauges For E14 And E27 Lamp Cap 7006-28A-1 Product Overview: Our Lamp Cap Gauges are meticulously designed to meet the dimensional and safety requirements outlined in IEC 60061-3, supporting compliance with IEC 60598-1, IEC 62560:2015, and other related lighting ...
IEC 60061-3 Lamp Cap Gauges Precision CNC Gauge Set for E26, GZ10, GX53, B15d, and E11 Testing
IEC 60061-3 Lamp Cap Gauges Precision CNC Gauge Set for E26, GZ10, GX53, B15d, and E11 Testing Product Overview: The Lamp Cap Gauges are manufactured in full compliance with IEC 60061-3, as required by IEC 60598-1, IEC 62560:2015, and related lighting standards. They are used for dimensional and ...
