|
| MOQ: | 1 |
| Price: | Customized |
| Standard Packaging: | Plywood |
| Delivery Period: | 1 Month |
| Payment Method: | T/T |
| Supply Capacity: | 15 Sets per Month |
IEC 60884: 2022 Cord Retention Testing Apparatus For The Effectiveness Of Cable
Product Information For Cord Retention Testing Apparatus:
This device conforms to the standard requirement of IEC 60884:2022 clause 23.2 figure 20.
It is for testing cord retention is for check the effectiveness of the retention of the cable of the cord anchorage.
The cord anchorage is used in the normal way, clamping screws, if any, being tightened with a torque equal to two-thirds of that specified in standard. After reassembly of the specimen, the component parts shall fit snugly and it shall not be possible to push the flexible cable into the specimen to any appreciable extent. The specimen is placed in the test apparatus so that the axis of the flexible cable is vertical where it enters the specimen.
Technical Parameters For Cord Retention Testing Apparatus:
Power supply: AC 220V±10%, 50Hz
Number of testing: 1~9999 (it is adjustable. 100 is by default.
Rate of testing: 60 times/min
Weight: 10N*1, 60N*1, 20N*2 (can achieve 30N, 40N, 50N, 60N)
Conforms to standard: IEC60884 clause 23.2 figure 20.
Attention For Cord Retention Testing Apparatus:
1. Lubricating oil should be added on the movable end of the guide rail regularly, to ensure that the test machine running smoothly
2. The flexible cord should be kept in vertical after the weights are hung on the cord, and the weight should be hung firmly to avoid falling during working, and damage the equipment, it is better to add a rubber plate on the bottom plate.
3. In normal use, the warranty period of the equipment is one year, we will continue to provide technical service after the warranty period.
1. Before install the test sample, can left rotate the speed adjust button to make the speed to be slower, observe when the mechanical arm moves down to the lowest position, press down the STOP button immediately.
Note: the speed adjust button is used to adjust the speed of the motor, thus to adjust the mechanical arm’s action speed. Right rotate this button to speed up, left rotate to slow down. When operator rotates the speed adjust button to make the mechanical arm action speed to match standard requirements, for example, 60 times/min (manually check by a stop watch), operator can mark the position, then next time test, operator just need to rotate the button to the mark position.
2. Loose the up cord clamp, select the appropriate cord bush (refer to the table below) according to the specifications of the sample, insert the cord bush into the entrance hole, then the cord of the specimen are across the cord bush, clamped by the up and lower cord clamps. After that, choose the appropriate weight based on the weight of the test requirements, the weights are hanged on the end of the cord, adjust the weight to the appropriate height, and the test can be started.
3. Access to the power supply, preset the test times on the counter.
Press “RESET” to clear the display value, then press the “RUN” button, the test starts, the test will automatically stop when reach to the setting times, press the “STOP” button when you want to stop during the half-way.
|
|
| MOQ: | 1 |
| Price: | Customized |
| Standard Packaging: | Plywood |
| Delivery Period: | 1 Month |
| Payment Method: | T/T |
| Supply Capacity: | 15 Sets per Month |
IEC 60884: 2022 Cord Retention Testing Apparatus For The Effectiveness Of Cable
Product Information For Cord Retention Testing Apparatus:
This device conforms to the standard requirement of IEC 60884:2022 clause 23.2 figure 20.
It is for testing cord retention is for check the effectiveness of the retention of the cable of the cord anchorage.
The cord anchorage is used in the normal way, clamping screws, if any, being tightened with a torque equal to two-thirds of that specified in standard. After reassembly of the specimen, the component parts shall fit snugly and it shall not be possible to push the flexible cable into the specimen to any appreciable extent. The specimen is placed in the test apparatus so that the axis of the flexible cable is vertical where it enters the specimen.
Technical Parameters For Cord Retention Testing Apparatus:
Power supply: AC 220V±10%, 50Hz
Number of testing: 1~9999 (it is adjustable. 100 is by default.
Rate of testing: 60 times/min
Weight: 10N*1, 60N*1, 20N*2 (can achieve 30N, 40N, 50N, 60N)
Conforms to standard: IEC60884 clause 23.2 figure 20.
Attention For Cord Retention Testing Apparatus:
1. Lubricating oil should be added on the movable end of the guide rail regularly, to ensure that the test machine running smoothly
2. The flexible cord should be kept in vertical after the weights are hung on the cord, and the weight should be hung firmly to avoid falling during working, and damage the equipment, it is better to add a rubber plate on the bottom plate.
3. In normal use, the warranty period of the equipment is one year, we will continue to provide technical service after the warranty period.
1. Before install the test sample, can left rotate the speed adjust button to make the speed to be slower, observe when the mechanical arm moves down to the lowest position, press down the STOP button immediately.
Note: the speed adjust button is used to adjust the speed of the motor, thus to adjust the mechanical arm’s action speed. Right rotate this button to speed up, left rotate to slow down. When operator rotates the speed adjust button to make the mechanical arm action speed to match standard requirements, for example, 60 times/min (manually check by a stop watch), operator can mark the position, then next time test, operator just need to rotate the button to the mark position.
2. Loose the up cord clamp, select the appropriate cord bush (refer to the table below) according to the specifications of the sample, insert the cord bush into the entrance hole, then the cord of the specimen are across the cord bush, clamped by the up and lower cord clamps. After that, choose the appropriate weight based on the weight of the test requirements, the weights are hanged on the end of the cord, adjust the weight to the appropriate height, and the test can be started.
3. Access to the power supply, preset the test times on the counter.
Press “RESET” to clear the display value, then press the “RUN” button, the test starts, the test will automatically stop when reach to the setting times, press the “STOP” button when you want to stop during the half-way.
